When you’re remodeling your home, you may be wondering how to run Ethernet cable through exterior walls. It can be a challenge to find an appropriate way to do this without damaging the wall or creating problems with noise and ventilation.
If you want to run an Ethernet cable through an exterior wall, there are a few things you will need to do. In this blog post, we’ll show you how to run Ethernet cable through exterior walls without any problems.
Requirements To Get The Job Done Successfully
First, you’ll need some supplies. You’ll need Ethernet cable, a drill, a screwdriver, and a drill bit. Next, you’ll need to line up your cables where you plan to run it.
Once you have the correct alignment, drill the hole in the wall and screw the cable into place. Finally, open up the wall and attach the cable to the wall.
A Comprehensive Guide to Running Ethernet Cable Through Exterior Walls
Here are some straightforward steps on how to run ethernet cable through exterior wall.
Examine Any Existing Installation
The first step is to check the existing Ethernet installation. Make sure that there is an outdoor-Rated Box installed and that the cables are properly secured from external elements. Suppose there is no outdoor-Rated Box, you will need to have one installed.
Mount an Outdoor-Rated Box
Make sure that there exists an outdoor-Rated Box installed and that the cables are properly protected from the elements. Suppose there is no outdoor-Rated Box, ensure to have one installed for you.
Ensure to mount the outdoor Rated Box on the outside of your house. You can do this using the screws that are provided with the box or by using a mounting bracket.
Choose ideal Cables And Connectors
You will need to choose a reliable cable for the job. For running through exterior walls, you will likely want to use a Category 5e or 6 cable. You can also use a Category 6a cable, but it will not be as effective at shielding against interference.
When choosing a connector, you should consider whether it is going to be used indoors or outdoors. You will also want to consider whether or not there is enough room for the connector and how easy it will be to get them connected in tight spaces.
Suppose are looking for an outdoor rated Ethernet box, you should check out TP-Link TL-SG108. There is an additional port on the back of it that allows you to connect more Ethernet cables without needing another box on your wall!
Select a Suitable Location To Run the Ethernet Cline
Once you have all of your supplies, you will need to choose a place to pass the Ethernet cable through the wall. You should make sure that there is a location in the wall where it will not be obstructed by anything and that it is easy to get to.
If you will be running the cable through an exterior wall, you may want to consider using a cable that has been rated for outdoor use. The easiest place is usually near an exterior wall jack.
Mark Exterior Wall
Mark the line on the exterior wall where you want to run your ethernet cable. You want to make sure that you are leaving enough room for proper installation of an outdoor-Rated Box.
Start Drilling a Hole Onto Your Exterior wall
After you have determined the route for your cable, you can start drilling a hole for it. Make sure that the hole is large enough to fit the cable through it. Drill the hole on the outside of the wall and be careful not to damage any wires or pipes that may be inside. You will need to make a hole in order for the cable to enter and exit your home.
Make sure that there are no pipes or wires behind where you are drilling. Drill slowly and carefully until you reach the other side of your exterior wall.
Run The Cable Through The Hole
At this point, you will need to run your cable through the wall. You should be sure that you have all of the necessary tools, such as a ladder, before attempting this. Use a fish tape to pull it through to the interior side.
Suppose you are not able to pull it through with your hands, you can use wire pulling lubricant. This will help keep the cable from getting stuck inside of the wall. Make sure that there is excess lubricant on both ends so that they do not stick together when they are pulled apart.
Tie off both ends and then run your Ethernet cable along with any other wires or cables inside of it. Make sure that they are all properly protected from moisture or outside interference by using waterproof sheathing or conduit pipe.
Install a Wall Jack
Next, you will need to install a jack on the outside of your house. You can do this with a drill or a screwdriver. Make sure that it is in the correct location and that it is secure. Use a drill bit that is slightly larger than the diameter of your Ethernet cable to make room for it. At this point, you are ready to start connecting devices to your network.
Cover The Hole
You will want to cover the existing hole with caulk or silicone sealant. Make sure that the sealant is weatherproof so that it will protect the cable from the elements. At this point you’re set to go.
How Do You Prevent Potential Problems With Power Lines Or Surges?
Suppose you want to run cable through exterior walls, you first need to determine the type of power line or surge protector that will be able to handle the cables. Next, find out how many wires the cable will need to be routed through the wall. Finally, make sure that the surge protector can handle the power lines and surges that might be involved in connecting your computer to the internet.
Conclusion
Ethernet cable is an important part of your networking and it can be a challenge to connect it correctly. With this guide you have learnt how to connect Ethernet cable successfully through exterior wall correctly and avoid any problems.